Olimex MSP430-H1611

Caution

This page is automatically generated from RIOT doxygen documentation. If you find any issues or have suggestions for improvement, please report them on Github.

View Doxygen Documentation View this board's documentation as generated by Doxygen.

View on GitHub View this board's source code on GitHub.

Tip

When using this board with RIOT, set the BOARD variable to olimex-msp430-h1611 in your Makefile. If you follow the standard RIOT project structure, your Makefile should look like this:

./Makefile

# name of your application
APPLICATION = hello-world

# Change this to your board if you want to build for a different board
BOARD ?= olimex-msp430-h1611

# This has to be the absolute path to the RIOT base directory:
RIOTBASE ?= $(CURDIR)/RIOT

include $(RIOTBASE)/Makefile.include

Support for the Olimex MSP430-H1611 board

MCU

MCU	TI MSP430F1611
Family	MSP430
Vendor	Texas Instruments
Package	64 QFN
RAM	10 KiB
Flash	48 KiB
Frequency	8 MHz
FPU	no
Timers	2 (2x 16bit)
ADCs	1x 8 channel 12-bit
UARTs	2
SPIs	2
I2Cs	1
Vcc	2.0V - 3.6V
Datasheet MCU	Datasheet
User Guide MCU	User Guide
Datasheet Board	MSP430-H1611 Datasheet
Website	MSP430-H1611 Website

Schematics

Pinout

The 64 pins on the edges of the PCB are connected to the corresponding MCU pins. Hence, the following pinout of the naked MSP430-F1611 MCU chip matches the pinout of the header board:

Flashing RIOT

Connect the board to a JTAG debugger supported by mspdebug; by default the Olimex MSP430-JTAG-Tiny (as shown in the picture above) is assumed, which is among the less expensive options.

Note: If you are not using the Olimex MSP430-JTAG-Tiny (or a compatible programmer), set MSPDEBUG_PROGRAMMER to the correct value via an environment variable or as parameter to make. E.g. use make BOARD=olimex-msp430-h1611 MSPDEBUG_PROGRAMMER=bus-pirate to flash using the bus pirate.

Warning: You can power the board via the JTAG programmer by placing a jumper at P_IN. However, the JTAG programmer will only be able to provide a limited current. You may want to disconnect the header board from devices consuming a lot of power prior to flashing.

Warning: If the board is powered externally, make sure to place the jumper in P_OUT position, not in P_IN position.

Warning: A jumper in P_OUT is mutually exclusive to a jumper in P_IN. Never connect both at the same time.

Note: Pin 1 on the JTAG connector has a small white triangle next to it and square pad, compared to the round pad used by all other JTAG pins.

Once the jumper is correctly placed in either P_IN or in P_OUT and the JTAG cable is connected just run

make BOARD=olimex-msp430-h1611 flash

Using the shell

stdio is available via the UART interface with TXD = P3.6 (pin 35 on the header) and RXD = P3.7 (pin 34 on the header) at 9,600 Baud.

The easiest way is to connect an USB TTL adapter (such as the cheap cp210x or ch341 based adapters) as follows:

TTL adapter    Olimex MSP430-H1611
-----------    -------------------

       GND --- 63 (DV_SS)
       TXD --- 35 (P3.7)
       RXD --- 34 (P3.6)